AxiTech — The Core of Precision
A 11 basic Analytical mill — main photograph
IKAAvailability: Supplied to order

A 11 basic Analytical mill

Reference 0002900000

A 11 basic Analytical mill laboratory stirrer from IKA. AxiTech covers the full lifecycle: installation and commissioning, planned preventive maintenance, periodic calibration, on-site troubleshooting, workshop repair and spare parts supply.

Request a service for this equipment

Nothing is charged online. Every request is reviewed by an AxiTech engineer before you receive a quotation.

At a glance

Reference
0002900000
Category
Shakers, Stirrers & Mixers

Overview

A 11 basic Analytical mill Batch mill for 2 different grinding procedures: Impact grinding of hard, brittle or non-elastic grinding materials with high-grade stainless steel beater. This beater can be used for a Mohs hardness up to 6 (incl. with delivery). Cutting grinding for pulverizing soft, fibrous materials with a cutting blade (not incl. with delivery). Moist and gluey materials can be pulverized by adding water Grinding chamber made of Tefcel (ETFE, glass fiber-reinforced) with stainless steel inlet (1.4571), useful volume 80 ml (incl. with delivery). For embrittlement of grinding materials with liquid nitrogen in the grinding chamber Optionally, a 250 ml grinding chamber is available Scope of delivery A 11 basic Analytical mill A 11.1 Spare beater

Maintenance contract — AxiTech provides planned preventive maintenance for A 11 basic Analytical mill from IKA: scheduled visits, safety checks, periodic calibration and a documented service report, backed by a contractual response time.

Troubleshooting, repair and spare parts — our shakers, stirrers & mixers engineers diagnose and repair A 11 basic Analytical mill on site or in the workshop, fit genuine spare parts and recommission the equipment after performance verification.

Features

  • Moist and gluey materials can be pulverized by adding water
  • Grinding chamber made of Tefcel (ETFE, glass fiber-reinforced) with stainless steel inlet (1.4571), useful volume 80 ml (incl. with delivery). For embrittlement of grinding materials with liquid nitrogen in the grinding chamber
  • Optionally, a 250 ml grinding chamber is available
  • A 11 basic Analytical mill
  • A 11.1 Spare beater

Technical specifications

Specifications
Weight
1.5 kg
Voltage
220 - 230 V
Frequency
50/60 Hz
Speed max.
28000 rpm
Power input
160 W
Process type
batch
Power ON time
1 min
Power OFF time
10 min
Feed hardness max.
6 Mohs
Motor rating input
160 W
Motor rating output
100 W
Operating principle
cutting/impact
Useable volume max.
80 ml
Feed grain size max.
10 mm
Dimensions (W x H x D)
85 x 240 x 85 mm
Material beater/cutter
stainless steel 1.4034
Material milling chamber
stainless steel 1.4571
Circumferential speed max.
53 m/s
Permissible relative humidity
80 %
Permissible ambient temperature
5 - 40 °C
Protection class according to DIN EN 60529
IP 43
Mill feed can be cooled in milling chamber with dry ice
yes
Mill feed can be cooled in milling chamber with liquid nitrogen
yes
Service coverage

AxiTech maintains, repairs and supplies this equipment for hospitals, clinics, laboratories and imaging centres.

Maintenance contracts for A 11 basic Analytical mill

AxiTech provides preventive maintenance contracts for A 11 basic Analytical mill. Each contract fixes a schedule of planned visits in which our biomedical engineers inspect the equipment, replace wear parts before they fail, and verify that it still performs inside the manufacturer’s tolerances.

Every visit includes calibration and performance verification, and closes with a documented maintenance report you can present during an accreditation audit. Spare-parts availability and a guaranteed response time are written into the contract, so a breakdown never leaves a department waiting for an answer.

Plan at least one preventive maintenance visit per year, and a second visit for equipment in continuous or critical use.

  • Planned preventive maintenance visits at a fixed interval
  • Calibration and performance verification against the manufacturer’s specifications
  • A documented maintenance report after every intervention
  • Guaranteed availability of spare parts and consumables
  • A contractual response time when the equipment fails

Discover our maintenance contracts

Planned preventive maintenance and calibration under contract

Troubleshooting and repair for A 11 basic Analytical mill

When A 11 basic Analytical mill fails, our engineers start with a structured diagnostic: error codes, electrical and mechanical checks, and a functional test against the equipment’s own specification. That tells us whether the fault is a consumable, a worn part or a board-level failure before any part is ordered.

Straightforward faults are repaired on site so the department loses as little time as possible. Anything that needs a workbench, a full strip-down or a specialised spare part goes to our workshop and comes back only after a complete post-repair test and, where the equipment requires it, recalibration.

Faults we see most often on this type of equipment

The faults we see most often are worn moving parts, power-supply and control-board failures, sensors that have drifted out of tolerance, and fluid or air paths that have become blocked or contaminated.

Discover our troubleshooting and repair service

Diagnostics, corrective repair and spare parts in the workshop
Troubleshooting

How to troubleshoot A 11 basic Analytical mill

Work through these checks before you escalate. They are the same first-line sequence our biomedical engineers run on arrival, and they either clear the fault or narrow it down enough that the intervention starts with the right spare part in the van.

  1. Capture the fault before you touch anything: write down the exact error code or message, the serial number from the rating plate, what the operator was doing and whether the fault clears on a restart.

  2. Confirm the power supply end to end — wall outlet, mains lead, fuse and any UPS or stabiliser in between. A device that is intermittently dead has a supply fault far more often than an internal one.

  3. Check the consumables and wear parts — filters, seals, tubing, probes, batteries — and note when each was last replaced. Anything past its service interval is the first suspect.

  4. Reproduce the fault once, deliberately, and record the sequence: what the operator did, what the device displayed, and whether a full power cycle clears it.

  5. If the fault is still there, escalate with the evidence. Send AxiTech the model, serial number, error code and the checks you have already run, and an engineer will come back with a diagnosis, a repair quote and a spare-parts lead time for A 11 basic Analytical mill.

What to send us when you report the fault

  • Manufacturer, model and serial number, from the rating plate
  • The exact error code or message, and the screen it appears on
  • When the fault started, how often it occurs and what triggers it
  • A photograph of the display or of the fault, and the last maintenance report

If the fault survives all five steps, stop using A 11 basic Analytical mill and open a repair request. Continuing to run equipment through a fault it cannot clear turns a component failure into a board-level one, and on devices used for diagnosis or therapy it puts the result — and the patient — in doubt.

Discover our troubleshooting and repair service

Buying and installing A 11 basic Analytical mill

AxiTech supplies A 11 basic Analytical mill together with the accessories and consumables it needs to enter service. We handle importation, delivery and installation, then commission the equipment on site so that it is verified against its specification before the first patient or the first sample.

Installation is followed by training for the users and for your biomedical team, warranty registration, and — if you want it — a maintenance contract that takes over the day the warranty ends, so the equipment never spends a period without planned service.

Discover our equipment sales service

Delivery, installation, commissioning and user training
Questions we are asked

Frequently asked questions about IKA A 11 basic Analytical mill

Yes. AxiTech services A 11 basic Analytical mill, either under a maintenance contract or as a one-off intervention. Our biomedical engineers cover preventive maintenance, calibration, corrective repair and spare-parts supply for this equipment.

Related equipment

Other IKA equipment we supply, install and maintain.