AxiTech — The Core of Precision
Automatic Double Water Still — main photograph
LabTechAvailability: Supplied to order

Automatic Double Water Still

Reference 2571522

Water still by LabTech: output 4L / 8L.

Request a service for this equipment

Nothing is charged online. Every request is reviewed by an AxiTech engineer before you receive a quotation.

At a glance

Reference
2571522
Category
Water Purification & Stills
Product range
Water Stills

Overview

Unique and compact design to be able to use at various places

With a built-in large storage tank, distilled water is ready for use

Fully automatic operation system

When the storage tank is full, it automatically cuts off water supply to prevent overflow

A prefilter is equipped as standard to prevent impurities from flowing into the distillerSafety : Over temperature protection Low water protection Electric leakage circuit breaker

Features

  • Capacity /hour: 4ℓ / 8ℓ
  • Reservoir : 8 L / 14 L
Service coverage

AxiTech maintains, repairs and supplies this equipment for hospitals, clinics, laboratories and imaging centres.

Maintenance contracts for LabTech Automatic Double Water Still

A service visit on the LabTech Automatic Double Water Still covers descaling of the boiler or heater, the condenser and water circuit, output water quality, cartridges and filters, and the level and safety controls.

Every visit includes calibration and performance verification, and closes with a documented maintenance report you can present during an accreditation audit. Spare-parts availability and a guaranteed response time are written into the contract, so a breakdown never leaves a department waiting for an answer.

Water stills and purification units like the LabTech Automatic Double Water Still are normally serviced once or twice a year, with the descaling interval set by the hardness of the feed water.

  • Boiler or heater descaled and cleaned
  • Output water quality checked by conductivity
  • Cartridges, resins and filters replaced as needed
  • Level controls, safety cut-outs and electrical safety tested

Discover our maintenance contracts

Planned preventive maintenance and calibration under contract

Troubleshooting and repair for LabTech Automatic Double Water Still

When LabTech Automatic Double Water Still fails, our engineers start with a structured diagnostic: error codes, electrical and mechanical checks, and a functional test against the equipment’s own specification. That tells us whether the fault is a consumable, a worn part or a board-level failure before any part is ordered.

Straightforward faults are repaired on site so the department loses as little time as possible. Anything that needs a workbench, a full strip-down or a specialised spare part goes to our workshop and comes back only after a complete post-repair test and, where the equipment requires it, recalibration.

Faults we see most often on this type of equipment

Frequent faults are scale on heating elements, exhausted cartridges giving poor water quality, failed level switches, and cooling-water flow problems.

Discover our troubleshooting and repair service

Diagnostics, corrective repair and spare parts in the workshop
Troubleshooting

How to troubleshoot LabTech Automatic Double Water Still

Work through these checks before you escalate. They are the same first-line sequence our biomedical engineers run on arrival, and they either clear the fault or narrow it down enough that the intervention starts with the right spare part in the van.

  1. Capture the fault before you touch anything: write down the exact error code or message, the serial number from the rating plate, what the operator was doing and whether the fault clears on a restart.

  2. Check the feed-water supply and the cooling-water flow: low pressure or flow stops distillation or trips the safety cut-out.

  3. Inspect the boiler for scale and descale it following the manual if deposits are visible.

  4. Measure the conductivity of the output water — a rising value means exhausted cartridges or carry-over.

  5. If the fault is still there, escalate with the evidence. Send AxiTech the model, serial number, error code and the checks you have already run, and an engineer will come back with a diagnosis, a repair quote and a spare-parts lead time for LabTech Automatic Double Water Still.

What to send us when you report the fault

  • Manufacturer, model and serial number, from the rating plate
  • The exact error code or message, and the screen it appears on
  • When the fault started, how often it occurs and what triggers it
  • A photograph of the display or of the fault, and the last maintenance report

If the fault survives all five steps, stop using LabTech Automatic Double Water Still and open a repair request. Continuing to run equipment through a fault it cannot clear turns a component failure into a board-level one, and on devices used for diagnosis or therapy it puts the result — and the patient — in doubt.

Discover our troubleshooting and repair service

Buying and installing LabTech Automatic Double Water Still

AxiTech supplies LabTech Automatic Double Water Still together with the accessories and consumables it needs to enter service. We handle importation, delivery and installation, then commission the equipment on site so that it is verified against its specification before the first patient or the first sample.

Installation is followed by training for the users and for your biomedical team, warranty registration, and — if you want it — a maintenance contract that takes over the day the warranty ends, so the equipment never spends a period without planned service.

Discover our equipment sales service

Delivery, installation, commissioning and user training
Product FAQ

Questions about the LabTech Automatic Double Water Still

Key specifications of the LabTech Automatic Double Water Still, according to the manufacturer: output 4L / 8L.

Related equipment

Other LabTech equipment we supply, install and maintain.